FILTERTIER LEARNReference guide

Water Testing

How to Read Your City Water Quality Report

Your annual Consumer Confidence Report is a starting point for understanding municipal source water, regulated contaminants and treatment.

How to Read Your City Water Quality Report

Your city water quality report—formally called a Consumer Confidence Report, or CCR—is the best first document for understanding the public water system that serves your home. It tells you where the water comes from, which regulated contaminants were detected, whether the utility had violations, what disinfectant is used, and how measured levels compare with federal or state standards. It does not tell you exactly what is coming out of your individual faucet today, and it does not include every possible contaminant. The right way to use a CCR is as a system-level baseline, then add home-specific testing only when the report, plumbing, local history, or household concern justifies it.

This guide walks through the report from top to bottom and explains the terms that confuse consumers most: MCL, MCLG, action level, treatment technique, 90th percentile, range, average, parts per billion, non-detect, violations, source water, lead service lines, PFAS, disinfectants, and emerging contaminants.

What is a Consumer Confidence Report?

A CCR is an annual drinking-water report prepared by community water systems. It summarizes information about the water source, detected regulated contaminants, compliance, and health information. Utilities generally publish or distribute the report each year for the previous calendar year’s data.

The report is designed for public communication, so it is more readable than a raw laboratory database—but it can still be technical.

What a CCR can tell you

  • which utility serves the system;
  • source-water type;
  • regulated contaminants detected;
  • highest levels or ranges reported;
  • regulatory limits or action levels;
  • whether violations occurred;
  • disinfectant and disinfection byproducts;
  • lead and copper monitoring summaries;
  • source-water vulnerability information;
  • contact information and public notices.

What a CCR cannot tell you

  • the exact lead level at your faucet;
  • every unregulated contaminant;
  • your home’s plumbing condition;
  • whether a filter in your house is working;
  • today’s exact concentration at your address;
  • every short-term distribution event;
  • private-well water quality.

Step 1: confirm the utility and report year

Many ZIP codes are served by more than one water system. Before reading numbers, confirm that the report belongs to your actual utility. Look at your water bill, municipal service information, or utility account.

Also check the report year. A report issued in 2026 may summarize 2025 monitoring. When comparing reports, use the sample dates and reporting period rather than assuming the publication year equals the measurement year.

Step 2: identify the water source

Utilities may use surface water, groundwater, purchased water, or a blend. Surface water comes from rivers, lakes, or reservoirs. Groundwater comes from wells. Some systems change sources seasonally or purchase treated water from another utility.

Source type influences likely treatment and contaminants but does not determine safety by itself.

Surface water

Surface water is more exposed to runoff and biological activity, so treatment typically includes robust filtration and disinfection. Source-water quality can change with storms, algal blooms, wildfire, industrial releases, and seasonal conditions.

Groundwater

Groundwater can be naturally protected from many surface contaminants but may contain minerals, hardness, iron, manganese, arsenic, nitrate, or industrial contaminants depending on geology and land use.

Purchased water

If your utility buys water from another system, the report may reference treatment or source information from the supplier. Distribution-system conditions in the purchasing utility can still matter after the water leaves the supplier.

Step 3: understand the contaminant table

The contaminant table is usually the core of the CCR. It lists substances detected during required monitoring and places the result beside regulatory benchmarks.

Common columns include contaminant name, MCLG, MCL, highest level detected, range, units, violation status, and likely source.

What is an MCL?

MCL stands for Maximum Contaminant Level. It is an enforceable drinking-water standard for a regulated contaminant under the applicable rule.

A reported value below the MCL generally means the system met that numerical standard for the monitoring period and compliance framework. A value above an MCL does not always translate into the same regulatory outcome because compliance can depend on averages, running annual averages, sample locations, or treatment requirements. Read the violation column and explanation.

What is an MCLG?

MCLG stands for Maximum Contaminant Level Goal. It is a non-enforceable public-health goal. The MCLG can be lower than the enforceable MCL because regulations also consider treatment feasibility, analytical capability, and other factors.

Do not treat an MCLG as if it were a utility violation threshold.

What is an action level?

Some rules use an action level rather than a simple system-wide MCL. Lead and copper are the classic examples. Monitoring is performed at selected taps, and the compliance calculation can depend on a percentile of results rather than an average.

An action level is not a statement that any amount below it is “safe” for every person, nor is a single household sample above it automatically proof that the utility violated the rule.

What is a treatment technique?

Some contaminants or risks are regulated through required treatment practices rather than a single numerical MCL. A treatment-technique violation means the system did not meet a required treatment or operational condition.

This distinction matters because a utility can have an important violation without a simple contaminant number exceeding a table limit.

What does “highest level detected” mean?

It usually refers to the highest compliance value relevant to that contaminant for the reporting period, but the calculation method can differ. It might be a single sample, an average, a running annual average, or another rule-defined statistic.

Read footnotes. The column heading alone may not explain the compliance calculation.

What does “range detected” mean?

The range shows low and high values across samples or monitoring locations. It helps reveal variability that a single average can hide.

A broad range may reflect different sources, seasons, sample locations, or distribution conditions.

Why average values can hide peaks

Some contaminants are regulated using averages. An average below the standard can coexist with individual samples above that number. This is not necessarily a violation if the rule is based on an average, but it can still be useful context for consumers.

Parts per million and parts per billion

Water reports commonly use ppm and ppb. One ppm is one part contaminant per million parts water; one ppb is one part per billion. Numerically, 1 ppm equals 1,000 ppb.

Do not compare numbers until the units match.

Milligrams per liter and micrograms per liter

For water, mg/L is approximately equivalent to ppm and µg/L is approximately equivalent to ppb for many practical drinking-water comparisons. Conversion still needs care, especially with other units.

Picocuries and other unfamiliar units

Radiological contaminants can use pCi/L. Microbiological indicators may use presence/absence or counts. Turbidity may use NTU. Disinfectants may use mg/L. Every unit belongs to a different kind of measurement.

“ND” or non-detect

ND means the laboratory did not detect the contaminant above the applicable detection or reporting limit. It does not mean there are literally zero molecules present.

When comparing PFAS or other very low-level contaminants, reporting limits are important.

Step 4: read the violation column carefully

A “No” in the violation column means the utility met the applicable requirement for that entry and reporting period. A “Yes” should lead you to the explanatory section, public notice, or corrective action.

Do not assume every detected contaminant is a violation. Drinking-water reports intentionally list detected contaminants even when they are far below limits.

How to read a violation

Look for:

  • what rule was violated;
  • when the violation occurred;
  • whether it is still open;
  • what population or area was affected;
  • what corrective action was taken;
  • whether an advisory was issued;
  • where current updates are posted.

Violation versus advisory

A boil-water advisory, do-not-drink notice, or other public-health advisory is not automatically the same thing as a Safe Drinking Water Act violation. Advisories can be precautionary and short-lived. Violations can involve monitoring, treatment, reporting, or contaminant standards.

FilterTier keeps these labels separate because consumers deserve accurate status language.

Open versus resolved violations

A historical violation can remain in an annual report after the underlying problem has been corrected. Check current utility and state regulator information before describing an old violation as active.

Step 5: read the lead and copper section differently

Lead is often primarily a plumbing and service-line issue rather than a contaminant leaving the treatment plant. Utilities monitor selected high-risk taps and report a percentile result.

What the 90th percentile means

For lead monitoring, the 90th percentile means 90% of sampled results were at or below that value under the relevant sampling set. It is not the maximum sample and it is not an average.

Your own home can be above or below the reported percentile.

Why a utility lead result cannot tell you your faucet level

Lead can enter water from a lead service line, solder, brass, fixtures, or building plumbing. Neighboring homes on the same utility can have very different lead results.

If your home has lead plumbing risk, a household tap test provides information the system-wide CCR cannot.

Lead service-line inventory

Utilities increasingly publish service-line material information. If your utility has an address-level inventory, check your property. An unknown material should not be treated the same as a confirmed lead service line, but it can justify additional investigation.

Step 6: look for disinfectant information

The report may show chlorine or chloramine residuals. Knowing which disinfectant your utility uses matters for home filtration because standard activated carbon and catalytic carbon can behave differently.

Chlorine

Free chlorine is commonly reduced with activated carbon. Whole-house carbon can improve taste and odor and reduce chlorine exposure at showers and fixtures.

Chloramine

Chloramine is more stable and can require catalytic carbon, greater media volume, or more contact time. A generic chlorine-rated filter should not automatically be assumed to provide equivalent chloramine performance.

Step 7: understand disinfection byproducts

Disinfectants can react with natural organic matter to form disinfection byproducts such as total trihalomethanes and haloacetic acids. Utilities monitor these under regulatory frameworks that can use locational running annual averages.

A single number in the report may therefore represent an average across time or a particular compliance location.

Why one year of DBP data is not the whole story

Disinfection byproducts can vary seasonally with temperature, source-water organic matter, disinfectant dose, and water age. Reviewing multiple years can reveal whether the system is stable or variable.

Step 8: read nitrate and nitrite results

Nitrate is especially important for infants and can be associated with agricultural runoff, septic systems, or natural conditions. Municipal systems monitor it under applicable rules.

A city-water nitrate result is useful system-level information; a private-well owner needs direct well testing instead.

Step 9: read arsenic results

Arsenic can occur naturally in groundwater and can also have industrial sources. If arsenic is detected in a groundwater-based system, review the actual level and trend rather than treating any detection as a violation.

Step 10: look for PFAS information

PFAS reporting is evolving as monitoring and regulatory requirements change. Some CCRs include regulated PFAS results directly; others reference separate monitoring pages or unregulated contaminant data.

When reading PFAS data, check compound names, units, sample dates, reporting limits, and whether results are screening data or compliance data.

Why “total PFAS” can be misleading

There are many PFAS compounds. A report may list individual compounds rather than one total. Different analytical methods include different compound lists, so “PFAS not detected” should always be read with the method and reporting limits in mind.

Step 11: review unregulated contaminants

Utilities may monitor contaminants that do not yet have federal MCLs. This monitoring helps EPA evaluate occurrence and potential future regulation. An unregulated detection is not automatically a violation.

What UCMR data means

The Unregulated Contaminant Monitoring Rule requires certain systems to monitor selected contaminants during defined cycles. UCMR data can be valuable for emerging contaminants, but it is occurrence data—not an automatic health determination.

Step 12: read source-water assessment language

Many reports summarize source-water susceptibility or protection programs. These sections can identify potential contamination sources around reservoirs, rivers, or well fields.

“Susceptible” does not mean the delivered water currently violates standards. It describes source vulnerability and the importance of protection and treatment.

Step 13: read health-information footnotes

CCR health language is standardized for certain contaminants and vulnerable populations. Read it, but distinguish general regulatory language from individualized medical advice.

If a household member has a condition that changes water-related risk, consult an appropriate health professional in addition to the utility report.

Example of a whole-house filtration system installed in a home
A city water report helps define treatment goals before equipment is purchased. A home filter should be matched to actual water data, plumbing, and household priorities.

How to decide whether a detected contaminant matters for home treatment

Use four questions:

  1. Is it regulated or unregulated?
  2. What was the actual level and unit?
  3. Is the result current and representative of my source?
  4. Does a home treatment technology have exact evidence for that contaminant?

Do not build a treatment system from the length of the contaminant table. Many listed detections can be well below standards.

When a city water report is enough

If the utility has stable compliance, your concern is chlorine taste, and the home has no special plumbing risk, the CCR may provide enough information to choose simple carbon treatment.

When you should test your own tap

Home testing becomes more useful when:

  • lead service-line or plumbing risk exists;
  • the home has unusual taste, odor, color, or sediment;
  • the building uses storage tanks;
  • you rely on a health-effect filter and want verification;
  • the property is at the edge of a distribution system;
  • a utility event or advisory recently occurred;
  • you have a private well;
  • the concern is not captured by the CCR.

What a home test cannot tell you about the whole utility

A single tap sample represents one location and time. It cannot establish system-wide compliance or prove that every other home has the same result. Household testing and utility compliance monitoring answer different questions.

How to compare multiple years of reports

Download three to five years of CCRs and track the contaminants you care about. Look for trends in source changes, disinfectant, PFAS, nitrate, arsenic, disinfection byproducts, lead percentile results, and violations.

A stable low result over multiple years gives different context from a rapidly changing series.

How to compare two utilities

Do not rank utilities simply by the number of detected contaminants. Different systems monitor different compounds at different frequencies and reporting limits. Compare compliance, source, treatment, relevant contaminant levels, and transparency.

Why a “zero contaminants” report would be suspicious

Modern laboratory methods detect substances at extremely low levels. A transparent report can list many detections while still showing excellent compliance. Detection is not the same as danger.

How to read hardness information

Hardness is usually an aesthetic/operational parameter rather than a federal health standard. Some utilities publish grains per gallon or mg/L as calcium carbonate. Hardness helps determine whether a softener or conditioner is worth considering.

How to convert hardness

A common conversion is roughly 17.1 mg/L as CaCO3 per grain per gallon. If the utility reports 171 mg/L hardness, that is about 10 grains per gallon.

How to read pH

pH affects corrosion, taste, scale, and treatment chemistry. Municipal systems manage pH as part of treatment and corrosion control. A CCR may list pH as an operating parameter even when it is not the main consumer concern.

How to read alkalinity

Alkalinity describes the water’s acid-neutralizing capacity and influences corrosion and treatment chemistry. It is not the same as pH.

How to read total dissolved solids

TDS represents dissolved minerals and salts. It does not tell you which specific ions are present and should not be used as a universal water-safety score.

How to read turbidity

Turbidity measures cloudiness from suspended particles and is important for treatment performance, particularly in surface-water systems. Compliance can be based on treatment-technique criteria rather than one simple consumer limit.

What “likely source” means

CCR tables often include a generic source description such as erosion of natural deposits, industrial discharge, fertilizer runoff, or treatment byproducts. This is explanatory language, not proof that the listed source caused the exact result in your system.

How to use the report for filter shopping

Build a short treatment brief from the CCR:

  • water source;
  • chlorine or chloramine;
  • hardness;
  • PFAS status;
  • lead/plumbing risk;
  • specific regulated detections that concern you;
  • violations or advisories;
  • peak household flow;
  • maintenance preference.

Then compare products against that brief instead of buying a filter with the longest contaminant list.

Why exact certification should follow the report

If the report shows PFAS and that is your priority, verify a PFAS-specific claim. If lead is the concern, verify lead. If the issue is chloramine, verify chloramine. Do not award treatment credit for unrelated certifications.

Example: chlorine, moderate hardness, no health-rule violations

A utility report shows free chlorine, moderate hardness, and routine regulated detections below limits. The household mainly dislikes taste and scale. A carbon filter plus softener or conditioner may be more rational than a complex PFAS/UV/RO bundle.

Example: chloramine and PFAS detections

The utility uses chloramine and reports PFAS. The homeowner wants whole-house treatment. The system now needs enough catalytic-carbon or other media capacity for chloramine plus credible PFAS evidence at household flow. This is a more demanding design than simple chlorine removal.

Example: low system lead percentile but old home plumbing

The CCR lead percentile is low, but the home was built during an era associated with lead service lines or solder. The system report cannot rule out a home-specific lead problem. Check the service-line inventory and consider tap testing.

Example: historical violation now resolved

A prior report lists a treatment violation, but current utility notices show the issue was corrected. The correct description is “historical/resolved,” not “the city currently has unsafe water.” Current status matters.

Common CCR mistakes

Comparing numbers with different units

Convert ppm, ppb, and other units before comparing.

Treating every detection as dangerous

Detection and violation are different.

Treating MCLG as the enforcement limit

MCLG is a non-enforceable health goal.

Assuming the report equals your faucet

Plumbing can change lead and other conditions.

Ignoring footnotes

Compliance calculations often live in the notes.

Ignoring the report year

Published reports often summarize the previous calendar year.

Reading an old violation as current

Verify status.

Buying treatment from a generic contaminant list

Match exact treatment to actual data.

CCR reading checklist

  1. Confirm utility.
  2. Confirm monitoring year.
  3. Identify source water.
  4. Identify disinfectant.
  5. Read violations first.
  6. Check lead and copper separately.
  7. Review PFAS and emerging-contaminant sections.
  8. Check hardness and pH if published.
  9. Note exact units.
  10. Compare with previous years.
  11. Check current utility notices.
  12. Decide whether home-specific testing is needed.

Frequently asked questions

Is my CCR proof that my tap water is safe?

It is strong system-level compliance information, but it does not measure your individual faucet or every possible contaminant.

What does a contaminant detection mean?

It means the laboratory measured the contaminant above the reporting threshold. Compare it with the regulatory benchmark and context.

What is the difference between MCL and MCLG?

MCL is enforceable; MCLG is a non-enforceable health goal.

What does “violation: no” mean?

The system met the applicable requirement for that entry and reporting period.

Why is my lead result different from the CCR?

Lead can come from your service line and plumbing, so household results vary.

Where do I find PFAS?

Check the contaminant table, emerging-contaminant section, UCMR data, or a separate utility PFAS page.

Does the report show hardness?

Some utilities publish it; others do not because hardness is not generally a federal health standard.

Should I filter every detected contaminant?

No. Prioritize meaningful concerns and products with exact evidence.

How often is the report updated?

Community water systems publish CCRs annually, while current advisories can update much more frequently.

What if I cannot find my report?

Contact the utility or local water department and confirm the system serving your address.

What this means for you

Your city water quality report is a starting point, not a verdict and not a shopping list. Read it in this order: confirm the utility, identify the source, check violations, understand lead, review the contaminant table and units, look for PFAS and disinfectant information, then decide whether home-specific testing is necessary.

Use FilterTier’s What’s in My Water? tool to connect your location to public water data, then use Find My Filter to match treatment to the actual issues you care about.

Primary references

How CCR compliance calculations can differ by contaminant

One of the easiest ways to misread a water report is to assume every contaminant uses the same compliance math. It does not. Some contaminants are compared with a maximum level in individual samples. Others use averages, running annual averages, locational averages, percentiles, or treatment-technique requirements. A utility can therefore report a high individual result without a violation when the rule uses an average, or it can have a violation without a dramatic contaminant number when the problem is monitoring or treatment technique.

When a number looks surprising, read the column heading, footnote, and rule-specific explanation before drawing a conclusion.

Running annual averages

A running annual average combines data from multiple quarters or sampling periods. It is designed to evaluate ongoing exposure or system performance rather than one moment. Disinfection byproduct compliance often uses forms of running averages. A high seasonal result can therefore influence the compliance value for several quarters.

Locational running annual averages

Some distribution-system contaminants are evaluated at individual monitoring locations because water age and local conditions differ. The compliance statistic can therefore be specific to one location rather than a system-wide average. This is especially relevant to disinfection byproducts in large systems.

Monitoring and reporting violations

A utility can have a violation because required samples were missed, collected late, or not reported correctly. That does not automatically mean the water exceeded a health-based contaminant limit. The violation still matters because monitoring is part of the safety framework, but the consumer should describe it accurately.

Treatment-technique violations

Treatment-technique rules require specific operational steps when direct contaminant measurement is not the only or best way to manage risk. A treatment-technique violation can be important even when the CCR does not show a dramatic contaminant number. Read the explanatory language to understand what requirement was missed.

How to read a CCR after a boil-water advisory

A boil-water advisory can occur between annual reports, so the next CCR may mention it only later. If you are investigating a recent advisory, use current utility notices and state-health information rather than waiting for the next annual CCR. The CCR remains useful for broader history and treatment context.

How to read a report after a source-water change

Utilities sometimes switch reservoirs, wells, or purchased-water suppliers. A source change can alter hardness, disinfectant, pH, mineral content, and contaminant profile. Compare reports before and after the change and review any utility explanation of treatment adjustments.

How to read a blended-water system

A utility that blends several sources can have seasonal or operational variation. One neighborhood may not literally receive the same blend every day. The CCR is still the right system-level reference, but home-specific testing can be useful if the treatment decision depends on a parameter that varies widely, such as hardness.

How to interpret “below detection limit” across years

Laboratories and methods can change. A non-detect at a reporting limit of 10 parts per trillion is not identical to a non-detect at 2 parts per trillion. When comparing PFAS or other trace contaminants over time, note the reporting limit rather than counting all non-detects as equivalent.

How to use state drinking-water databases with the CCR

The annual report is the consumer-friendly summary. State regulator databases can provide more detailed compliance history, violations, monitoring periods, and enforcement status. If a CCR lists a violation that you want to understand deeply, the state database is often the next source to check.

How EPA system data complements the report

Federal drinking-water databases can show public-system identifiers, violations, enforcement actions, and inventory information. They are valuable for research, but the records can be technical and may lag current utility updates. Use them together with the utility and state regulator rather than treating one database as the entire story.

Why local reporting can be useful—but secondary

Credible local journalism can explain what happened during a contamination event, how residents were affected, and what officials said. For regulatory status, exact contaminant numbers, and current advisories, primary utility and regulator sources should remain the foundation.

How to distinguish source-water contamination from distribution contamination

A contaminant can enter before treatment, form during treatment, or enter through distribution and plumbing. PFAS in a source well is a different problem from lead released by a home service line. Disinfection byproducts form as disinfectants react with organic matter, while bacteria can enter after a pressure loss. The treatment location should follow the contamination mechanism.

Why “city water is contaminated” can be too broad

A utility may have one affected well, one monitoring location, one neighborhood, or one temporary incident. Good interpretation identifies the scope rather than turning a local result into a system-wide claim without evidence.

How to read emergency notices alongside the CCR

Current notices should answer immediate action questions: boil, do not drink, flush, or no action. The CCR answers annual context questions. During an active event, follow the current notice first and use the CCR to understand the system afterward.

How to identify your exact water system when a city has several

Large cities, suburban ZIP codes, and county areas can have multiple public systems. Some homes use municipal water while nearby properties use private wells. Confirm the utility account name or system identifier before matching a CCR to an address.

Why ZIP code alone can be insufficient

ZIP boundaries are postal, not water-system boundaries. One ZIP can cross utility service areas. This is why FilterTier’s water-data work resolves utilities rather than assuming one report per ZIP.

How to use a CCR before buying a softener

Find hardness if the utility reports it, or request the current hardness range. If the value varies seasonally, size the softener for the higher realistic hardness. Do not buy a softener merely because the report lists calcium or magnesium.

How to use a CCR before buying carbon filtration

Determine whether the utility uses chlorine or chloramine. Then look at aesthetic goals and any organic contaminant concerns. A large GAC tank can be excellent for chlorine; chloramine may justify catalytic carbon and more contact time.

How to use a CCR before buying PFAS treatment

Record the exact PFAS compounds, units, source dates, and whether the values are current. Then verify the exact filter claim and capacity for those compounds. Do not buy a product because the word PFAS appears anywhere in its marketing.

How to use a CCR before buying UV

Municipal water is already disinfected, so UV is generally not the first response to a city-water CCR. It can make sense as a redundant barrier after whole-house carbon or in unusual building conditions, but a PFAS or lead detection is not a reason to buy UV.

How to use a CCR before buying reverse osmosis

RO can address a broad range of dissolved contaminants at the drinking-water tap. If the CCR shows nitrate, PFAS, arsenic, or high dissolved solids relevant to your goals, an exact certified RO system may be a practical point-of-use option. Compare the system’s exact claims rather than assuming every membrane covers every contaminant.

How to build a one-page water profile from the report

CategoryYour notes
UtilityName and system ID
SourceSurface, groundwater, purchased, blended
DisinfectantChlorine or chloramine
HardnessRange if available
Lead90th percentile + service-line status
PFASCompounds, levels, dates
ViolationsCurrent, historical, resolved
Other concernsNitrate, arsenic, DBPs, taste/odor

This profile is much more useful for filter shopping than carrying around the entire report.

What to save for future comparison

Download the PDF or save a copy of the current report. Utilities redesign websites and replace links. Keeping the actual annual report makes it possible to compare trends later. Save any current PFAS data sheet or lead-service-line record separately because those can update more often than the CCR.

How often should you reread the report?

Review the new CCR annually and whenever you move, the utility changes sources, or a major water-quality event occurs. High-interest parameters such as PFAS or lead-service-line status may deserve more frequent checks from current utility pages.

What a good water-report interpretation should sound like

A careful summary says, “The utility detected X at Y level in the reported period, below/above the applicable benchmark, and the current status is Z.” A weak summary says, “This city has toxic water” based on one historical detection. Precision protects both consumers and credibility.

Final rule for reading your report

Separate four questions that are often blended together: What was detected? Was the utility in compliance? What does the result mean for my individual home? What treatment, if any, is justified? The CCR answers the first two very well. Plumbing records and home testing may be needed for the third. The fourth requires matching treatment evidence to the actual problem.

What to do after you finish reading

Turn the report into one or two decisions, not a shopping spree. If the main issue is chloramine, research catalytic-carbon systems. If the report is clean but the house has an unknown lead service line, investigate the service line and test the tap. If PFAS is reported, compare PFAS-specific treatment evidence and decide whether point-of-use or whole-house treatment fits your goals. If nothing in the report or plumbing points to a meaningful problem, the right decision may be no additional treatment at all.

A CCR is most valuable when it narrows uncertainty. Use it to eliminate unnecessary equipment, identify the few issues that deserve deeper research, and establish a baseline you can revisit each year. That evidence-first process is more reliable than buying a filter designed to claim it treats hundreds of contaminants regardless of what is actually in your water.

Read the data, verify the context, then treat only the problem that actually exists.

How to Read a City Water Quality Report | FilterTierUse your annual Consumer Confidence Report to understand source water, detected contaminants and what additional home testing may still be useful.How to Read Your City Water Quality Report